Plateau Egg Holder Emu or Nandu FIEM

✅ Original FIEM 🚚 24h Shipping 🇮🇹 Italian assistance ⭐ 45 years of experience

📌 Scroll below for a complete guide, compatibility, and installation.

Original Fiem spare parts from Padovan Avicoltura : Complete Digital Thermostat DIG1 Fiem spare parts. We rely exclusively on original spare parts from the manufacturers of each product, so you don't have to resort to non-original parts that could compromise the proper functioning of your product and consequently cause irreparable damage and risks to your safety.

ATTENTION: PRODUCT DISCONTINUED

The original Fiem control unit is no longer available. It has been replaced by the manufacturer with an upgrade kit that includes the new control unit and specific wiring harness for the adaptation.

[Link to the new replacement kit]

ADVICE BEFORE PURCHASE

Since this is a repair on incubators that have been in service for many years, we recommend carefully evaluating the overall condition of the machine. Consider whether repair costs are the most cost-effective option in the long run, or whether investing in replacing the entire incubator is more cost-effective.

✅ Original FIEM 🚚 24h Shipping 🇮🇹 Italian assistance ⭐ 45 years of experience

📌 Scroll below for assembly and maintenance guide.

Complete tank with floating group for artificial breeder

Simple and effective humidity control with the FIEM Humidity Kit

This complete kit is the ideal solution for those looking to automate humidity management within their FIEM incubator. Consisting of a tank with a plexiglass lid and float, an ultrasonic nebulizer with a membrane, an external tank, and a connecting tube, it ensures uniform and constant distribution of water vapor, improving environmental conditions for optimal hatching.

Perfect for small breeders, hobbyists, and professionals, this accessory is compatible with numerous FIEM models (except the MG50 CIP CIP 28-40 EI PLASTIC MODELS) equipped with a control unit set up for automatic humidity control. Installation is quick and easy, with no complex technical intervention required.

Positive reviews on the web: Appreciated for its ease of use, reliability in maintaining humidity parameters, and compatibility with many FIEM incubators.

Criticisms found on the web: Some users recommend checking the membrane periodically to ensure maximum efficiency.

Original Fiem Spare Parts : Incubation basket for quail measuring 38x35 cm.

Capacity approximately 70 quail eggs suitable for Fiem MG70/100 Incubator, Fiem MG 100/150 Incubator, Fiem MG 140/200 Incubator.

The quantity of eggs is indicative and varies depending on the size. To secure the eggs upright, we recommend purchasing the appropriate springs (see photo).

Only at Padovan Avicoltura can you find an efficient spare parts service guaranteed over time to keep your incubator in top working order, as well as pre- and post-sales assistance.

See reviews from other breeders by clicking HERE REVIEWS (a serious review service managed directly by Google with verified rated reviews).

Want to ask for information or clarification directly via WhatsApp? Click WHATSAPP

Original Spare Parts for Fiem Incubator : MG50 Useful for those who want to avoid dirtying the incubation drawer supplied with the machine.

Only at PadovanAvicoltura can you find an efficient spare parts service guaranteed over time to keep your incubator in top working order, as well as pre- and post-sales assistance.

See other breeders' reviews by clicking HERE BREEDERS' OPINIONS  

Original Fiem Spare Parts : Riccioli (1pc) Resistance Holder for Fiem MG50 Incubator

Trust Padovan Avicoltura: Only Made in Italy incubators and original spare parts

Original Fiem Spare Parts : Single Egg Turning Bar for Fiem MG140/200 Incubator

Trust Padovan Avicoltura: Only Made in Italy incubators and original spare parts

A customer from Padua called me on the 10th day of incubation: the temperature was constantly fluctuating between 36°C and 36.2°C. After checking, the heating element had lost electrical continuity in one spot. I urgently replaced it with the original FIEM R75E, the temperature stabilized immediately, and the eggs hatched successfully.

When is it needed? If your incubator never reaches the set temperature , or takes too long to heat up, or if the thermostat is always on but the heat doesn't increase, the heating element is probably faulty. Abnormal temperature fluctuations can also indicate a damaged heating element.

⚠️ Before ordering: Unplug the power cord, disconnect the resistor, and measure the electrical resistance with a tester : it should read approximately 505 Ohms (2.06 m × 245 Ohms/m). If it reads "infinity" or significantly different values, the resistor is broken. Also check that there are no cuts, burns, or blackened spots on the wire.

📸 Don't have a tester? Send us a photo of the installed resistor on WhatsApp and describe the incubator's behavior: we'll help you diagnose it before purchasing.

Installation: Electrical work that requires care. Always unplug the appliance and, if you are unfamiliar with electrical connections, consult a qualified technician.

💰 Price: €12.18 (VAT excluded, shipping excluded) – FIEM WAREHOUSE COMO

Compatibility: Both the CIP CIP 28 and CIP CIP 40 models use the same R75E resistor.

Minimum order €20: Add other useful spare parts (fuse, fixing collars, thermometer) to complete the order.

📦 Logistics: Ships in 1 business day, delivery 2-4 days. Warranty: 24 months for private individuals / 12 months for VAT numbers.

The Fiem humidity tray lid , compatible with the MG and Astrale series, is an original spare part designed to simply yet effectively regulate humidity inside the incubator . During incubation, humidity is generated naturally through the evaporation of the water contained in the tray. However, when the ambient humidity is already high or excessive humidity occurs inside the machine, it is useful to reduce the evaporating surface to bring the values back within optimal limits. This lid allows you to partially cover the tray , limiting evaporation and stabilizing the internal microclimate. It is a simple system, but essential for successful hatching. Each Fiem incubator in these series is equipped with a standard lid , but having an additional one is always recommended: it can be used as a spare or for more flexible humidity management in variable conditions, by covering the tray with 2 pieces.
🔧 Original Fiem steel spare part 14x9 cm
✅ Compatible with MG and Astrale
🛠️ Useful in high humidity conditions

When are they needed? When replacing the R75E resistor, it's essential to check the condition of the collars. If they're worn, broken, or missing, they should be replaced along with the resistor.

💰 Price: €1.58 (VAT excluded, shipping excluded) – FIEM WAREHOUSE COMO

Minimum order €20: Add R75E resistor (€12.18) + fuse (€0.42) + thermometer (€22.05) for a complete maintenance kit.

📦 Logistics: 1-day shipping, 2-4 day delivery. Warranty: 24 months for private individuals / 12 months for VAT numbers.

Spare Parts and Exotic Options Fiem 12/230v power supply for Jolly and transport nest

Power supply for SIR actuator